Need Help?

X10 PRO Inductive Dimmer Switch: for Ceiling Fans and 4A Motors

Item # XPDI3-WI

This product has been discontinued.

This item weighs 0.35lbs.

View all X-10 Pro products

Product Description

Responds to "ALL Lights ON". Rated at 500 Watts. Neutral required. No feed through connectors. White & Ivory rockers included.

The XPDI3 (3-way master/single pole) Incandescent & Inductive Dimmer Module is designed to control incandescent loads with a rating of between 40W and 500W and tip to 5Amp inductive loads. Lamps rated below 40W may flicker or operate erratically. A Companion Switch (XPSS) is available for three and four-way operation. A removable decorative paddle is located on the Wall Dimmer Module for local ON/OFF and BRIGHTEN/DIM control. A power cutoff switch located only on the Wall Dimmer Module, directly below paddle, is provided for bulb changing.


Note: To use as a single pole module simply cap off the RED Wire. Incandescent and Inductive Dimmer Modules can be used to control Incandescent loads up to 500W, low voltage lighting power supplies, and ceiling fan motors. The XPDI3 does require the use of a Neutral Wire at the wall box. The Ground Wire is not used.

Installing the Wall Dimmer Module (used as a three way)
  • Disconnect power at the circuit breaker.
  • Remove switch plates and unscrew existing switches from their boxes, Identity the Line, load and traveller wires at each existing switch (usually connected to a different color terminal).
  • Replace one of the existing wall switches with the Incandescent & Inductive Dimmer Module XPDI3.
  • The Load connects to the glue wire on the module.
  • The Red wire from the XPDIS is connected to a traveller wire going to the Switch position on the XPSS Slave.
  • I2OVAC can be supplied by either the Master or the Slave position and sent over on a traveller wire to the black wire on the XPDIS and the Live position on the XPSS. In a single pole application line and Load should be in the salve box.
  • Connect the White wire from the module to Neutral.

Setting up the Wall Dimmer Module
  • Set the House Code dial under the removable decorative paddle) to the same letter set on the controller or Security Console. The House Code for monitored security consoles is downloaded by the security installation firm. The default House Code is A, when using the PR02000.
  • For normal lighting control, set the Unit Code dial to an unused code which can be controlled from the controller or an RF remote such as the Security Remote, PSROI (switches 1-4 control Unit Codes 1-4).
  • To use as the security light, set the Unit Code to the match the Unit Code of the security console. The Unit Code for monitored security consoles is downloaded by the security installation firm. The default Unit Code is '13', when using the PR02000.

    Note: The security light is the light which is flashed on/off during an alarm and is controlled by the security LIGHT ON and LIGHT OFF buttons on the PRO2~O console, keychain and security remotes)
4-Way Applications
When creating a four-way application, simply parallel another XPSS across the same two travellers from the first Slave location, Connect wires from Switch to Switch and Live to Live, using the feed thru screw terminals.

More Info


How X10 Works

X10 communicates between transmitters and receivers by sending and receiving signals over the power line wiring. These signals involve short RF bursts which represent digital information.

X10 transmissions are synchronized to the zero crossing point of the AC power line. The goal should be to transmit as close to the zero crossing point as possible, but certainly within 200 microseconds of the zero crossing point. The PSC05 provides a 60 Hz square wave with a maximum delay of 100 µsec from the zero crossing point of the AC power line. The maximum delay between signal envelope input and 120 kHz output bursts is 50 µsec. Therefore, it should be arranged that outputs to the PSC05 be within 50 µs of this 60 Hz zero crossing reference square wave. .
A Binary 1 is represented by a 1 millisecond burst of 120 kHz at the zero crossing point, and a Binary 0 by the absence of 120 kHz. The PSC05 modulates its input (from the O.E.M.) with 120 kHz, therefore only the 1 ms "envelope" need be applied to its input. These 1 millisecond bursts should equally be transmitted three times to coincide with the zero crossing point of all three phases in a three phase distribution system. Figure 1 shows the timing relationship of these bursts relative to zero crossing. .
. .
A complete code transmission encompasses eleven cycles of the power line. The first two cycles represent a Start Code. The next four cycles represent the House Code and the last five cycles represent either the Number Code (1 thru 16) or a Function Code (On, Off, etc.). This complete block, (Start Code, House Code, Key Code) should always be transmitted in groups of 2 with 3 power line cycles between each group of 2 codes. Bright and dim are exceptions to this rule and should be transmitted continuously (at least twice) with no gaps between codes. See Figure 2. .
. Within each block of data, each four or five bit code should be transmitted in true compliment form on alternate half cycles of the power line. I.E. if a 1 millisecond burst of signal is transmitted on one half cycle (binary 1) then no signal should be transmitted on the next cycle, (binary 0). See Figure 3.

The Tables in Figure 4 show the binary codes to be transmitted for each House Code and Key Code. The Start Code is always 1110 which is a unique code and is the only code which does not follow the true complimentary relationship on alternate half cycles. .

[1] Hail Request is transmitted to see if there are any X10 transmitters within listening range. This allows the O.E.M. to assign a different Housecode if a "Hail Acknowledge" is received.

[2] In a Pre-Set Dim instruction, the D8 bit represents the Most Significant Bit of the level and H1, H2, H4 and H8 bits represent the Least Significant Bits.

[3] The Extended Data code is followed by 8 bit bytes which can represent Analog Data (after A to D conversion). There should be no gaps between the Extended Data code and the actual data, and no gaps between data bytes. The first 8 bit byte can be used to say how many bytes of data will follow. If gaps are left between data bytes, these codes could be received by X10 modules causing erroneous operation.

Extended Code is similar to Extended Data: 8 Bit bytes which follow Extended Code (with no gaps) can represent additional codes. This allows the designer to expand beyond the 256 codes presently available. .

NOTE 1 . X10 Receiver Modules require a "silence" of at least 3 power cycles between each pair of 11 bit code transmissions (no gaps between each pair). The one exception to this rule is bright and dim codes. These are transmitted continuously with no gaps between each 11 bit dim code or 11 bit bright code. A 3 cycle gap is necessary between different codes, i.e. between bright and dim, or 1 and dim, or on and bright, etc.

NOTE 2. The PSC05 Two-Way Power Line Interface cannot receive Extended Code or Extended Data because these codes have no gaps between them. The PSC05 can only receive standard "pairs" of 11 bit X10 codes with 3 power line cycle gaps between each pair.

NOTE 3. The PSC05 can receive dim and bright codes but the output will represent the first dim or bright code received, followed by every third code received. i.e. the output from the PSC05 will not be a continuous stream of dim and bright codes like the codes which are transmitted.

A Square wave representing zero crossing detect is provided by the PSC05 and is within 100 &s of the zero crossing point of the AC power line. The output signal envelope from the O.E.M. should be within 50 &s of this zero crossing detect. The signal envelope should be 1 ms (-50µs +100µs). See Figure 5. .
Opto-Coupled 60 Hz reference output (from the PSC05)
Transmissions are to be synchronized to the zero crossing point of the AC power line and should be as close to true zero crossing as possible. The PSC05 is designed to be interfaced to other microprocessor circuitry which outputs X10 codes synchronized to the zero crossing point of the AC power line. It is therefore necessary to provide a zero crossing reference for the O.E.M. microprocessor.

It is likely that this microprocessor will have its own "isolated" power supply. It is necessary to maintain this isolation, therefore the trigger circuit normally used in X10 controllers is not desirable as this would reference the O.E.M. power supply to the AC power line. It is also not desirable to take the trigger from the secondary side of the power supply transformer as some phase shift is likely to occur. It is therefore necessary to provide an opto-coupled 60 Hz reference.

An opto-coupled 60 Hz square wave is provided at the output of the PSC05. X10 codes generated by the O.E.M. product are to be synchronized to this zero crossing reference. The X10 code envelope generated by the O.E.M. is applied to the PSC05 which modulates the envelope with 120 kHz and capacitively couples it to the AC power line.

Opto-Coupled Signal Input (to the PSC05)

The input signal required from the O.E.M. product is the signal "envelope" of the X10 code format, i.e.

High for 1 ms. coincident with zero crossing represents a binary "1" and gates the 120 kHz oscillator through to the output drive circuit thus transmitting 120 kHz onto the AC power line for 1 ms.

Low for 1 ms. coincident with the zero crossing point represents a binary "0" and turns the 120 kHz oscillator/output circuit off for the duration of the 1 ms. input. .

Opto-Coupled Signal Output (from the PSC05)

The "X10 received" output from the PSC05 coincides with the second half of each X10 transmission. This output is the envelope of the bursts of 120 kHz received. Only the envelope corresponding to the first burst of each group of 3 bursts is available at the output of the PSC05. See Figures 6, 7, and 8. .


Source: X10 WorldWideWeb pages

Manuals for X-10 Pro

No products are currently available from this category.
Unavailable/discontinued items are listed below for your reference.

Unavailable / Discontinued Items

Additional Photos

XPDI3-WI - Large View

Back to Top

Interested in Home Automation, but don't know where to start?

Choosing a Home Automation System: A guide for Do-It-Yourselfers

Start Here

Plan Your Systems

Structured Wiring Systems

Complete Structured Wiring Systems from Leviton and ChannelVision Central.

Free E-Book: Home Automation Basics

Learn More